Cung cấp tất cả các loại bore đạn TFS - Tsubaki Japan , NFS, ASNU ( Stieber ), VSNU ( GMN ), USNU - VP-Technik, 202--020 Rexnord, TCK - Trame: TFS8, TFS12, TFS15, TFS17, TFS20, TFS25, TFS30, TFS35, TFS40, TFS45, TFS50, TFS60, TFS70, TFS80, TFS90, TFS100, TFS120, TFS150, TFS200.
one way bearing for automachine, textile machine, mining machine. TFS, TFS-C,TSS,FSO,MG,B200,MX,MI,MA,MA,PB,BST,MZEU,BSEU,CSK.
Dimensions and capacities
Model
Torque Capacity (N.m)
Max.Overrunning Speedr/mm
Internal diameter H7(mm)
External diameter h6(mm)
Length C (mm)
Keyway (mm)
Inner Race
Outer Race
TFS12
32
4500
2300
12
35
13
4x1.8
4x1.4
TFS15
34
3500
1800
15
42
18
5x1.2
5x1.8
TFS17
60
3200
1600
17
47
19
5x2.3
TFS20
100
2500
1300
20
52
21
6x1.6
6x2.3
TFS25
154
2000
1000
25
62
24
8x2.0
8x2.8
TFS30
270
800
30
72
27
10x2.5
TFS35
570
1400
700
80
31
10x2.4
12x3.5
TFS40
728
650
40
90
33
12x2.2
12x4..1
TFS45
907
1100
550
45
36
14x2.1
14x4.6
TFS50
1349
500
50
110
14x5.6
TFS60
2370
840
420
130
46
18x2.3
18x5.5
TFS70
3017
750
380
70
150
51
20x2.7
20x6.9
TFS80
4370
670
340
170
58
22x3.1
20x7.5
Installation and Usage
1. The outer race of the TFS Series Cam Clutch was designed for press fit installation to the housing. Correct interference dimensions of the outer race must be maintained to option maximum clutch performance. The internal diameter for the housing should meet the H7 tolerance of the JIS standard. Keyways should be made in the end faces of clutch for proper installation. Refer to item 3 in the installation and usage for CSK. Series Cam Clutches for information on the installation method. If the tolerance of the internal diameter of the housing is K6, keyways are not required on the end faces of the clutch. 2. Make sure the housing has enough strength to withstand the pressure required for the press fitting installation of the clutch. 3. When installing the clutch, mount it with a type 63 bearing to avoid radial force, since this clutch does not have any bearings inside. 4. The clutch should be mounted on the shaft by rotating it in the direction marked by the arrow shown on the clutch plate. 5. The recommended shaft tolerate is H7, and the key profile should be in accordance with the following standard. TFS 12 ......DIN 6885.1 TFS 15~80 ......DIN 6885.3 6.Suitable surface pressure of the key should be selected according to your company design standards.
Lubrication 1.Oil lubrication is recommended. 2. Do not use greases or lubricants with EP additives.
SD TECHNOLOGY AND TRADING SERVICE CO., LTD
© 2003-2024 |
CÔNG TY TNHH TMDV & KT SD
CÔNG TY TNHH TMDV & KT SD
Mô tơ (3)
